Product

Double Row Angular Contact Ball Bearings

Innovative Products for Home & Gifts

Double row angular contact ball bearing is composed of an inner ring, an outer ring, ball and cage components. Cage materials include nylon, sheet steel or brass. The structure of double row a...

share with:
SEND EMAIL TO US CONTACT US ONLINE
Message Board
Got a question? If you can’t find what you are looking for, contact us using one of the methods below- we’d be happy to help!

Product information

Characteristic

Double row angular contact ball bearing is composed of an inner ring, an outer ring, ball and cage components. Cage materials include nylon, sheet steel or brass. The structure of double row angular contact ball bearing is similar to the narrowing slightly pair of O-type arrangement of angular contact ball bearings. But it differs in that the contact angle and ferrule design, it is a high rigidity of the bearing arrangement to withstand the overturning moment.

Double row angular contact ball bearings are divided into open, seal and split inner ring design. Because standardized manufacturing process, for open bearings, the seals or dust cover is formed with grooves placed on the outer ring. Sealed bearings are maintenance-free, so you can achieve particularly economical bearing arrangement. Angular contact ball bearing angular adjustment is very limited.

Open designed double row angular contact ball bearings can withstand axial loads and high radial loads. Double row angular contact ball bearing is particularly suited to the need to achieve a rigid axial guide bearing configuration. 32A and 33A series double row angular contact ball bearings with optimized internal geometry, no filling slots, contact angle of 30°, the structure is back to back configuration.

Sealed design double row angular contact ball bearings can provide bearings with seals or dust cover at the same time. 32A and 33A series of bearings marked with high-quality lithium grease, this grease has a good anti-corrosion function, can be used at a temperature from -30°to + 120°. Sealed bearings were lubricated for life time use and require no maintenance, but should never be cleaned before installation or heated above 80℃.

Bearings with split inner ring can be put into more and larger balls, and therefore have a higher carrying capacity, especially axial load. 33D series bearing with contact angle of 45°, with a special internal clearance and can withstand heavy axial loads in both directions, the bearings are separable design, the outer ring and the ball – cage and the inner ring can be installed separately. 33DNRCBM series bearing with contact angle of 40°, the outer ring with snap groove and snap ring, these can be done axial positioning in the bearing housing and simplify the bearing arrangement and space-saving, non-isolated design.

Sealing solutions

Shielded bearings, suffix 2Z, provide two kinds of different structural design.

Bearing with a ring, the suffix 2RS1, which being made of strip seal skeleton nitrile rubber (NBR), the outer seal into the groove and can provide a good seal. These seals allow the operating temperature from -40 to 100℃, in a short time up to + 120℃.

Lubrication

Sealed bearings use high-quality bearing grease lubrication,these greases can meet the requirement of the bearing lubrication in the operational life cycle.

Misalignment

When there is an angle error between the inner and outer rings of the double row angular contact ball bearing, balls and raceways will lead to bear a greater load. Any angle error will result in increased noise and shorten the working life of the bearing.

Operating temperature

KMR angular contact ball bearings undergo a special heat treatment, equipped with a steel or brass cage, bearings can operate at temperatures up to + 150℃. bearing of Nylon 6,6 cage operating temperature can reach to +120℃.

In continuous high temperature operating conditions or adverse conditions, it is recommended to use pressed steel cage or machined brass cage bearings.

Cage

Card-type glass fiber reinforced polyamide 6,6 cage ball guide, suffix TN9

Card-type pressed steel cage, ball guide, no suffix or suffix J1

Crown type pressed steel cage, ball guide, no suffix

Machined window-type brass cage, outer ring guide, the suffix MA

Machined window-type brass cage, ball guide, suffix M

We can supply other forms of retainer by consensus.

Existing suffix design

Suffix

Instruction

A

无装球缺口

No filling slots

CB

特定的轴向游隙

Controlled axial internal clearance

C2

轴向游隙小于普通组

Axial internal clearance smaller than Normal

C3

轴向游隙大于普通组

Axial internal clearance greater than Normal

D

剖分内圈

Two-piece inner ring

J1

冲压钢保持架,钢球引导

Stamped steel cage, ball centred

M

机削黄铜保持架,钢球引导

Machined brass cage, ball centred

MT33

锂基增稠润滑脂,温度范围-30至120℃

N

外圈带止动槽

Snap ring groove in the outer ring

NR

外圈带止动槽和止动环

Snap ring groove in the outer ring, with appropriate

nap ring

2RS1

两侧带具钢骨架的丁腈橡胶密封圈

Contact seal, NBR, on both sides

TN9

卡型玻璃纤维增强尼龙6,6保持架,钢球引导

Glass fibre reinforced PA66 cage, ball centred

2Z

两侧带冲压钢防尘盖

Shield on both sides




KMR logo

+86 531-66695622

yjx@kmr.cn.com

+86 531-66695627 / 531-66695621

Copyright © 2011-2016 Shandong KMR bearing Science & Technology Co.,Ltd.   Technical support: sdzhidian