Product

Four-point contact ball bearings

Innovative Products for Home & Gifts

Four point contact bearings are single row angular contact ball bearings, specially designed raceways enable it to withstand axial load in both directions, the radial load is a percentage of the a...

share with:
SEND EMAIL TO US CONTACT US ONLINE
Message Board
Got a question? If you can’t find what you are looking for, contact us using one of the methods below- we’d be happy to help!

Product information

Features

Four point contact bearings are single row angular contact ball bearings, specially designed raceways enable it to withstand axial load in both directions, the radial load is a percentage of the axial load. These bearings share the less axial space than double row angular contact ball bearing. KMR four-point contact ball bearings and standard range includes QJ2 QJ3 series.

Bearing composed by outer ring, split inner ring, balls and cage assembly, cage being made of brass or polyamide material. Split inner ring can accommodate as many as balls. Double half-bearing inner ring is specific match, even if the same size bearings can not be split with another bearing inner ring interchangeable. The bearings are separable design, ie the outer ring even ball - cage assembly and two-piece inner ring can be installed independently.

The outer ring with positioning groove or without locating groove

With two-way axial load carrying capacity of four-point contact ball bearings are often used in combination with a radial bearing, and is used as thrust bearings and with clearance in bearing housing. In order to quickly and reliably positioned, the large size of the four-point contact ball bearing outer ring has two locating grooves and spaced 180 °. These bearings have the suffix N2.

Radial and axial load capacity

Since the bearing raceway with a high wall, the contact angle of 35 ° and contact with as much as rolling elements, so this design of four point contact ball bearings has a higher load carrying capacity. Be able to withstand larger bi-axial and small radial loads.

The outer ring with positioning groove or without locating groove

With two-way axial load carrying capacity of four-point contact ball bearings are often used in combination with a radial bearing, and is used as thrust bearings and with clearance in bearing housing. In order to quickly and reliably positioned, the large size of the four-point contact ball bearing outer ring has two locating grooves and spaced 180 °. These bearings have the suffix N2.

Sealing Solutions

Four point contact ball bearings are open design.

Lubrication

No initial installation of the lubricant, lubricated with grease or oil lubrication is workable.

Cage

Machined brass cage, outer ring, the suffix MA

Injection molded window-type glass fiber reinforced polyether ether ketone (PEEK) cage, outer ring guide, the suffix PHAS.

At high temperatures, the aging of lubricants and oil additives can reduce the operating life of the plastic holding frame. We must comply with oil change intervals.

Other forms can supply cage by consensus.

Operating temperature

KMR four-point contact ball bearings undergo a special heat treatment, equipped with steel, brass or PEEK cage bearings, it can operate at temperatures up to + 150 ℃. Four point contact ball bearings with brass cages suitable to operating temperature range of -30 ℃ to + 150 ℃. Bearing diameter than 240 mm, dimensionally stable temperatures up to + 200 ℃. With glass fiber reinforced nylon cage bearing maximum operating temperature up to + 120 ℃.

Suffixes

Instruction

B20

Reduced width tolerance

C2

Axial internal clearance smaller than Normal

C2H

Axial internal clearance in the upper half of the C2 range

C2L

Axial internal clearance in the lower half of the C2 range

CNL

Axial internal clearance in the lower half of the Normal range

FA

Machined steel cage, outer ring centred

MA

Machined brass cage, outer ring centred.

N2

Two locating slots (notches) in one outer ring side face, 180° apart

PHAS

Glass fibre reinforced PEEK cage, with lubrication grooves in the guiding surface,

outer ring centred

S1

Bearing rings heat stabilized for operating temperatures ≤ 200 °C(390 °F)


KMR logo

+86 531-66695622

yjx@kmr.cn.com

+86 531-66695627 / 531-66695621

Copyright © 2011-2016 Shandong KMR bearing Science & Technology Co.,Ltd.   Technical support: sdzhidian